How We Remove a Hot Tub on Long Island

All Island crew walking through a hot tub removal job with a homeowner

Step 1

Walk the job

We confirm access, the tub's build (acrylic shell, fiberglass, wood-skirted), and where the dump truck can park. If the tub is sunken into a deck or surrounded by lattice, we plan the access path first, usually 5 minutes.

A drained hot tub ready for removal on Long Island

Step 2

Confirm the tub is drained

Draining is the one step that's on you, and it needs to happen before we arrive: a 400-gallon tub empties slowly. Run a hose from the drain port to a sanitary or street drain (where local code allows) so the yard stays usable, and clear the dregs with a wet vac. We confirm it's empty and get to work.

Disconnecting a hot tub from electrical and water lines

Step 3

Disconnect electric & water

Most hot tubs are hardwired into a 240V GFCI breaker plus a water feed. We shut the breaker, cap the lines, and pull the panel cover so the next person knows it's safe. We do NOT touch live electrical. If it's not already isolated at the panel, we ask you to call your electrician first.

Cutting a hot tub shell into truck-sized sections

Step 4

Cut the shell

Acrylic shells crack into hundreds of sharp pieces if you swing a sledgehammer at them. We section the shell with a reciprocating saw (usually 6 to 8 cuts on a standard 4-person tub) into pieces that fit through your gate. Cleaner, safer, no broken decking around the install pad.

Loading hot tub components onto the All Island truck

Step 5

Carry out & load

Sectioned shell pieces, cabinet panels, motor, pump, heater, and frame all go on the truck. Two-person crew handles a standard tub in 90 minutes from arrival. Larger swim spas or in-ground sunken tubs take 2-3 hours.

Hot tub components being routed to recycling facilities

Step 6

Haul to recycling + transfer

Acrylic shell sections go to a transfer station. Copper plumbing and metal frame get separated and routed to a metal recycler where accepted. The motor and pump go to e-waste recycling.

Step 7

Site cleanup

Sweep the pad, pull stray screws and brackets, and walk the path. If decking was opened to get the tub out, we leave the boards stacked and let you know what needs to go back. The job ends with you having a usable pad, not a debris zone.

Common questions

Hot tub removal FAQ.

How long does a hot tub removal take?

About 90 minutes for a standard 4–6 person above-ground tub. Swim spas, sunken tubs, or tubs with limited access can run 2–3 hours. We confirm the time estimate during the on-site quote, before anything starts.

Do I need to drain the hot tub before you arrive?

Yes. Draining is the one step that's on you. Run a hose from the tub's drain port to a sanitary or street drain (where local code allows) rather than onto the lawn, and clear the last few inches with a wet vac. Start it the day before; a 400-gallon tub takes hours to empty. Everything after that is ours.

Will the wood deck around the hot tub get damaged?

Not under normal removal. We cut the tub into sections small enough to lift out without prying. If access is genuinely too narrow, we discuss removing a few deck boards before we start. Boards are stacked, not damaged, and the homeowner replaces them. We don't do deck restoration.

Can you remove an in-ground or sunken hot tub?

Yes. Sunken tubs are slower because we have to break out the shell from inside the pit, then haul material up. Adds 1–2 hours typically. We can also fill and patch the pit, but that's a separate scope we quote on-site.

What does a hot tub removal cost on Long Island?

Pricing covers the cut, haul, and disposal, all-in: larger swim spas or sunken tubs cost more than a standard above-ground tub. We give you one flat number on-site before anything starts. Full pricing details are on our pricing page, linked in the footer.

How we remove a hot tub.